Description

Technical Parameters

ASB Stainless steel manifold with flow meter are manufactured from stainless to the highest standards.Use higher quality brass raw material, 100% leakage testing before shipping. Contact us for more details of Stainless steel manifold with flow meter!!!

Product Description

Stainless steel manifold with flow meter

ASB Stainless steel manifold with flow meter are manufactured from stainless to the highest standards.

A unique feature is that connections to the heating pipe are Speed-fit Push-fit, offering much-reduced installation time

All manifolds are pre-fitted with brackets, vibration isolation mounts, and an automatic air vent. Flow rate indicators include the means to adjust flow rate and isolate circuit.

It can be assembled to suit left or right-hand supply depending upon project type.

Download catalogue: stainless steel manifold with flow meter

Technical specification

NOTE: This checklist refers exclusively to fittings from our Underfloor Heating range. Other fittings, valves, tube and ancillary products have their own Technical Specification.

Applications: Underfloor Heating Installations in solid or timber floors.

Pipes: 15mm ASB Barrier Pipe to BS 7291, Parts 1, 2 and 3 Class S.

DO NOT USE ASB Underfloor Heating Products for Gas, fuel oil or compressed air applications.

Floor Insulation: Should be a suitable material and thickness to comply with current regulations.

Minimum Bending Radii: For ASB Pex-b Pipe is 175mm.

Expansion (PEX-Pipe): 1% on the length between 20°C and 82°C.

Paint and Chemicals: Only use water or oil based paint. DO NOT ALLOW CONTACT WITH cellulose based paints, paint thinners or strippers, solder flux, acid based descalants or aggressive household cleaning products.

Exposure to Sunlight: ASB products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting.

Pipe Inserts:. Must be used on all installations when using plastic pipe and should be fully inserted.

Electrical Components: Electrical products in the ASB Underfloor Heating Systems are designed only to be used in U. K. Electrical Supply situations.

Electrical Continuity: If ASB is used in an existing metal system which may have been used for earthing, electrical continuity should be reinstated.

Collet Clips: White and Grey collet clips are used with standard fittings to prevent accidental pipe disconnection. Red or blue clips provide colour coding of the pipe. Red and blue clips should not be used to prevent accidental release of the pipe.

Pre-Screed System Testing: To ensure the pipework has been installed correctly prior to the screed being laid, it is essential that the system is checked and hydraulically wet tested.

Testing should be carried out at 2 bar for 10 minutes and 10 bar for 10 minutes.

This testing, combined with other relevant checks, should reveal installation problems and is regarded as good plumbing practice.

Pressurisation During Screed Laying & Curing: In accordance with BS1264-4, the system should be left under pressure at a minimum of 6 bar for the duration of the laying and curing of the screed.

Under NO circumstances should the UFH System be used to quicken the screed drying process.

System Flushing: As is usual practice for any plumbing installation, flushing of the system prior to the use of ASB is recommended to remove any contaminants/chemical residue from elsewhere in the system.

Vermin: ASB products should not be used in vermin infested areas.

Frost Protection: During the installation process it is important that pipe containing water is protected from frost.

Technical data:

Working pressure: PN 6Bar

Working temperature:-20℃- +80℃

Sub tube amounts: 2-12 ways

Diameter at the two ends: G-1"

Material: 304Stainless steel

Code	Size	Ways	L(mm)	D(mm)
53010/53110	1"	2	104	50
53010/53110	1"	3	154	100
53010/53110	1"	4	204	150
53010/53110	1"	5	254	200
53010/53110	1"	6	304	250
53010/53110	1"	7	354	300
53010/53110	1"	8	404	350
53010/53110	1"	9	454	400
53010/53110	1"	10	504	450